Guangzhou Yihua Plastic Products Co., Ltd.

Faithful cooperation, superior quality and satisfactory services

  welcome to consult us by phone

 18688888124

In injection molding of PET preforms, what are noteworthy?

Click: Time:2020-11-18 16:26:14 From:Zhihu

1. Plastic treatment

PET, as a macromolecule, contains ester groups and is somewhat hydrophilic. The granular PET is relatively sensitive at high temperature. When moisture content goes beyond the limit, the molecular mass of PET will decline during processing. The products thereby manufactured will be colored and fragile. Therefore, prior to processing, the materials shall be dried for more than 4 hours at 150℃. Generally, they shall be dried for 3 to 4 hours at 170℃. Whether the materials are completely dry can be tested by air shot. In general, no more than 25% materials shall be recycled, and the recycled materials shall be thoroughly dried up.


2. Selection of injection molding machines

PET keeps stable for a shorter time after reaching the melting point, which is relatively high, so it is necessary to select injection systems with multiple temperature ranges which produce little heat for friction during plasticization. Besides, the actual weight of products (including drainage opening materials) shall not be lower than 2/3 of the injection quantity. In consideration of these requirements, Hwamda has developed small and medium-sized special plasticization systems for PET over the past years. The plasticization systems with a clamping force above 6300t/m2 can be used.



3. Mold and gate design

PET preforms are generally molded with hot runner molds. It is better the put a heat insulation plate between a mold and the formwork of an injection molding machine. The heat insulation plate shall be approximately 12mm thick and must withstand high pressure. The exhaust must be adequate to avoid local overheating or crack, whereas the vent depth generally shall not exceed 0.03mm, or else burr will easily form.


4. Hot melt glue temperature

Measure the temperature with air shot. The temperature ranges between 270℃ and 295℃. For enhanced GF-PET, the temperature can be set between 290℃ and 315℃.

 

5. Injection speed

Generally, the injection shall be fast to prevent too early solidification during injection. However, over speedy injection and high shear rate easily make materials fragile. The injection shall be generally completed within 4s.


6. Back pressure

The back pressure shall be as low as possible to avoid wear. Generally, it shall not exceed 100bar. In general, back pressure needn’t be used.


7. Residence time

The residence time must not be too long, to prevent molecular mass from declining. The temperature shall not exceed 300℃ if possible. If the device is shut down for fewer than 15min, only air shot will be needed. If the shutdown lasts more than 15min, clean the device with viscous PE, and decrease the barrel temperature to the PE temperature until the device is powered on again.

 

8. Notes

1) The recycled materials must not be too bulky, or else they will be easily piled up like “a bridge” in the feeding zone, thereby impacting plasticization. 2) If mold or material temperature is improperly controlled, “white fog” will be produced, thus making the products opaque. Low and uniform mold temperature, fast cooling and little crystallization make the products transparent. 


Contact Us

——

FAX:020-26035481

TEL:18688888124

E-mail:771063273@qq.com

Address: 30 Yuanding Road, Daluo, Zhongluotan Town, Baiyun District, Guangzhou

联系我们

——

传真:020-26035481

电话:020-86035481

邮箱:771063273@qq.com

地址:广州市白云区钟落潭镇大罗园顶路30号101室

 

 

English
  • 中文
  • English
图片展示

Scan It To Browse The Mobile Website

Contact Us

——

FAX: 020-26035481

TEL: 18688888124

Email: 771063273@qq.com

Address: 30 Yuanding Road, Daluo, Zhongluotan Town, Baiyun District, Guangzhou

 

 

All rights reserved: by Guangzhou Yihua Plastic Products Co., Ltd.    Website: https://www.yihuapet.com   Website map      Suggest previewing with a resolution of 1920*1080  Technical support:D.F.X Design      Y.ICP. No. 2021001151

Contact Us
TOP
Contact Us
Contacts
TEL
18688888124
E-mail
771063273@qq.com
Address
30 Yuanding Road, Daluo, Zhongluotan Town, Baiyun District, Guangzhou
TOP
Service Center
Qrcode
Alibaba
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.